Skip to content
Weddings and events

How to record audio at a wedding: vows, toasts and reception, with a backup for every word

Updated 13 min read

Short answer

To record audio at a wedding, capture every spoken moment on two sources: a lav on the groom and on the officiant, a recorder on the DJ's soundboard for the toasts, and the camera mic as a sync reference. Record at 48 kHz and monitor on headphones. Then upload the cleanest track to FilmScribe and get vows transcribed by speaker.

Step by step

  1. 01 Write the audio plan before the day List the vows, the officiant's words and the toasts, and write a main source and a backup next to each. Every important line gets recorded twice.
  2. 02 Test every mic the day before Batteries charged, cards formatted, clocks matched, recorders at 48 kHz and a one-minute test on every mic, checked on headphones.
  3. 03 Roll continuously and monitor Start the recorders before guests walk in, keep the camera mic on and wear headphones through the vows and the toasts.
  4. 04 Make two copies and name the files Copy the cards to two drives and rename each audio file with the date, the couple, the moment and the source before you format anything.
  5. 05 Upload the cleanest audio to FilmScribe Upload the WAV or MP3 from the lav or the recorder with Wedding as the content type, and mark a start and an end if you only need the ceremony or the toasts.
  6. 06 Read, star and take it to your editor Get every line transcribed by speaker, with chapters and emotions, star the lines for the film and, on Studio and Agency, export a cut timeline.
In this guide
  1. In short
  2. How to record wedding audio and log it with FilmScribe
  3. What is the audio plan for each part of a wedding?
  4. Why does audio decide the wedding film?
  5. What gear do I need to record wedding audio?
  6. Where do I put the lav on the groom and the officiant?
  7. How do I record audio from the DJ’s soundboard?
  8. Which settings should I use: 48 kHz, 24-bit or 32-bit float?
  9. Wedding day audio checklist
  10. How do I sync external audio with wedding video?
  11. What should I upload to FilmScribe to log the wedding?
  12. What if the wedding audio came out bad?
  13. What do you get on each FilmScribe plan?
  14. Other ways to handle wedding audio
  15. Common wedding audio mistakes
  16. Frequently asked questions
  17. Sources

A wedding has no second take. If the groom’s lav drops out during the vows, nobody runs the scene again: the film loses the one line the couple most wanted to hear. That is why wedding audio recording gets planned backwards from the picture. The backup comes first, the main mic second.

FilmScribe comes in once the recording is done. You upload the lav or recorder audio and get the vows and toasts back word for word, with each speaker separated and timestamped, ready for logging. We don’t record, sync or clean up audio: the better it arrives, the better the text. This guide covers both halves, the recording and what to do with the files afterwards. For a lecture, a meeting or an interview, see how to record and transcribe audio.

In short

  • Two sources for every line. A lav on the groom and on the officiant, a recorder on the soundboard and the camera mic as reference.
  • Lav outside the clothing, six to eight inches below the chin, with the cable taped so it can’t rub.
  • Ask before you plug into the board and use the recorder’s line input. On a mic input, the signal distorts.
  • Record at 48 kHz, 24-bit, with headroom for the loudest moment. In 32-bit float, a clipped-looking peak comes back in post.
  • Monitor on headphones and let the recorders roll without stopping.
  • After the wedding: two copies, sync in your editor and the cleanest audio in FilmScribe for logging.

How to record wedding audio and log it with FilmScribe

1. Write the audio plan before the day

List the lines you can’t miss: the vows, the officiant’s words, the toasts. Next to each one, write the main source and the backup, as in the table in the next section. If you can, record the rehearsal: Shure’s audio guide for video recommends it as the chance to fine-tune your setup before the real thing. Keep the plan with your wedding shot list.

2. Test every mic the day before

Charge the batteries, format the cards, match the date and time on cameras and recorders, and record one minute on each device. Listen on headphones. If a mic also plugs into your computer, the mic test shows peak, speech level and noise floor in 8 seconds.

3. Roll continuously and monitor

Start the recorders before guests walk in and stop only when the moment is over: nobody warns you before the best man grabs the mic. Keep your headphones on through the vows and the toasts.

4. Make two copies and name the files

Before you go to bed, copy the cards to two drives. Rename each audio file with the date, the couple, the moment and the source, like 2026-10-17_emma-and-james_ceremony_groom-lav.wav.

5. Upload the cleanest audio to FilmScribe

Pick the track where the voice is cleanest: usually the lav for the vows and the soundboard for the toasts. WAV, MP3, M4A and other formats are accepted, up to 10 GB per file, and the content type is Wedding. If the recorder rolled for six hours, mark where the ceremony starts and ends before processing: only that range is transcribed and counts toward your plan’s hours.

If the voice only exists on the camera file, upload the video, or first extract audio from video to get just the sound as MP3 or WAV.

6. Read, star and take it to your editor

We return the transcript word for word, with a timestamp on every word, each speaker separated, chapters and emotions. Search “promise” to land on the vows, star the lines that belong in the film and download any passage as MP3, TXT, PDF or SRT. On Studio and Agency, your selects become a cut timeline for your editor. Choosing the lines is covered in how to do a paper edit.

Want to try it on a wedding you shot? The trial runs 3 days with 1 hour of material and needs a card on file.

What is the audio plan for each part of a wedding?

One rule: every important line lands on two independent recordings. If one fails, the other saves the film.

MomentMain sourceBackup
Officiant’s wordsLav on the officiantRecorder on the venue’s soundboard
VowsLav on the groomOfficiant’s lav and the camera mic
Toasts and speechesRecorder on the DJ’s soundboardSmall recorder near the speaker
Dance floor and roomCamera micRecorder in a corner of the room

The camera mic stays on the whole time: it is the sound your editor matches against the recorder to line up external audio with picture.

Why does audio decide the wedding film?

Because the film is built on the spoken word. The vows and the father’s toast are the spine of the story, and the footage plays over them. A shaky shot can be swapped for another angle. A line that was never recorded can’t be swapped for anything.

Speech also speeds up the edit: once it is transcribed, you search for the line instead of scrubbing through the whole ceremony, as shown in how to edit a wedding video. And what matters most is the distance between mouth and mic, not the price of the gear. According to Shure, each time that distance doubles, the sound pressure level reaching the mic drops to a quarter.

What gear do I need to record wedding audio?

The minimum that covers the day is three pieces, plus headphones, wind protection, tape, and spare batteries and cards:

  • A wireless lav that records inside the transmitter. Wireless links drop, and the internal recording keeps the line anyway. RØDE’s Wireless GO II guide, for example, describes the feature: each transmitter stores over 40 hours of compressed audio or around seven hours uncompressed, and Backup mode starts recording when the transmitter connects to the receiver. It has to be switched on beforehand in the maker’s app.
  • A portable recorder with a line input, for the soundboard, ideally 32-bit float.
  • A shotgun mic on the camera, for ambience and for the reference sound.

The ideal kit adds a second lav for the officiant and a small backup recorder, which Shure suggests hiding in the pocket of the best man or the officiant. With wireless lavs, Shure also recommends fresh batteries right before the event and a walkaround of the space, listening for dropouts, before guests arrive.

Where do I put the lav on the groom and the officiant?

On the groom. It is the most important mic of the day, because it sits between the two people saying the vows. Shure’s lavalier advice applies: outside the clothing, about six to eight inches below the chin, clipped to a lapel, a pocket or a tie. To hide it, Shure suggests placing the lav behind the groom’s boutonniere, once the flowers are in place, and dressing the cable inside the coat. The transmitter goes in the inside pocket.

On the bride, it is rarely possible: the dress has nowhere to hold a transmitter. Shure flags the cost of that choice: the bride may end up harder to hear than the groom. Ask the couple to stand close and face each other for the vows.

On the officiant. A lav at chest height, outside the robe or the jacket. The officiant is always next to the couple, which makes this the best backup for the vows.

Three things apply to everyone:

  • Nothing rubbing. The mic and the first few inches of cable can’t touch fabric, a necklace or a beard. Tape the cable down inside the clothing.
  • Collars muffle. Clipped to a shirt collar, a lav sounds dull, because some of the high frequencies don’t reach the area under the chin.
  • Battery life counts. The Wireless GO II, for example, runs up to seven hours per charge, according to RØDE: switch it on close to the ceremony, not during bridal prep.

In a church, the problem is reverb, and it rarely comes out in post: only a mic close to the mouth avoids it. Outdoors, it is wind: put a windscreen on every mic, lavs included, and turn on the recorder’s low-cut filter if it has one.

How do I record audio from the DJ’s soundboard?

During the toasts, the microphone belongs to the DJ or the band, not to you. Shure puts the rule plainly: if there are other people’s mics at the event, one of them will be used for something important, and you need a plan for it. The plan is to record the board’s output.

  1. Ask first. Talk to the DJ or the sound tech when you arrive, not when the first toast starts, and ask which output on the board is free.
  2. Check the level: line or mic. A board output is usually line level, a signal about 10,000 times stronger than a microphone’s, according to Shure. On a mic-level input, it comes in loud and distorted. Switch the recorder’s input to line.
  3. Set the level for the loudest moment. The “check, one, two” is quieter than an excited best man. Leave headroom, turn on the limiter and, if the recorder has one, the safety track, which records a copy at a lower level.
  4. Let it roll. Hit record before dinner, lock the buttons and stop after the last toast.
  5. Keep an acoustic backup. A second recorder aimed at a PA speaker, a few feet away and not right up against it, captures the toasts the way the room heard them.

What the board doesn’t give you is the room. Laughter, applause and tears come from the camera mic or from an ambience recorder.

Which settings should I use: 48 kHz, 24-bit or 32-bit float?

SettingWhat to useWhy
Sample rate48 kHzIt is the rate used for video
Bit depth24-bit, or 32-bit float if the recorder has itFloat forgives the unexpected peak
FormatWAVUncompressed, for editing and mixing
Level, at 24-bitPeaks between -12 and -6 dBFS at the loudest momentHeadroom for laughter and applause
Camera auto gainOff, with an external micIt pumps the level up and down

At 24-bit, levels matter: if the signal goes past the ceiling, the peak is cut off and it doesn’t come back. It is the working format on a lot of gear: the Wireless GO II transmitter, for example, records uncompressed at 48 kHz, 24-bit, according to RØDE. The -12 to -6 dBFS range is the same one our mic test uses.

32-bit float changes that math. According to Zoom, which makes recorders in this format, you don’t need to set gain while recording, and a peak that looks clipped can be recovered later by lowering the file’s gain in post. The cost is storage: about 33% more than the same audio at 24-bit. The format won’t fix a badly placed mic, rubbing fabric or wind.

A safety track is the fallback when you record at 24-bit: a second copy of the signal at a lower level. On the Wireless GO II, the safety channel sits 20 dB below the main one and only works in the mode that merges both transmitters into one output, according to RØDE.

How much storage to bring: a 48 kHz, 24-bit WAV takes about 520 MB per hour in mono and 1 GB per hour in stereo.

Wedding day audio checklist

Copy it and make it yours:

AUDIO CHECKLIST: [couple], [date]

Day before
[ ] Batteries charged, cards formatted, clocks matched
[ ] Recorders set to WAV, 48 kHz, 24-bit or 32-bit float
[ ] Recording inside the lav transmitter switched on
[ ] One-minute test on every mic, on headphones

Ceremony
[ ] Lav on the groom and the officiant, cable taped
[ ] Recorder on the soundboard, input set to line
[ ] Windscreens (outdoors)
[ ] Everything rolling before the processional, headphones on

Reception
[ ] Agreed with the DJ: board output and time of the toasts
[ ] Board recorder with limiter on and buttons locked
[ ] Backup recorder aimed at a PA speaker

Afterwards
[ ] Two copies of every card before formatting

How do I sync external audio with wedding video?

In your editor, after the backup: that step isn’t ours. In Final Cut Pro, the command is Clip > Synchronize Clips. According to Apple, it looks for sync points in markers, timecode, file creation date and audio content, and the “Use audio for synchronization” option fine-tunes the sync using the waveforms. The original clips are left untouched. For DaVinci Resolve, Blackmagic Design describes multicam syncing by audio waveform, timecode or in and out points. In Premiere Pro or any other editor, the logic is the same: the camera sound is the reference for lining up the recorder.

Two things help in any editor:

  • Reference sound on every camera. With no camera audio, there is no waveform to match.
  • A clap at the start. With everything rolling, clap your hands in front of the camera. The spike shows in the picture and in the sound, and it works as a manual sync point when the automatic one fails. It is the method Shure’s guide teaches.

If the audio drifts out of sync little by little, suspect the video: a phone used as a backup camera often records at a variable frame rate. The video metadata viewer tells you whether the frame rate is constant or variable.

What should I upload to FilmScribe to log the wedding?

The audio with the cleanest voice, one file per moment:

  • One source per moment. The groom’s lav and the officiant’s lav recorded the same lines. Uploading both transcribes the ceremony twice and uses double the hours.
  • 32-bit float. Set the gain in your editor and export a 24-bit WAV or an MP3 copy to upload, with the voice at a healthy level.
  • Slow venue Wi-Fi. The WAV to MP3 tool makes a light copy just for the upload. The original WAV is still the audio for the film.
  • A recording in pieces. If the recorder split the reception into several files, run them through the audio joiner before uploading. On Agency, you can upload up to 20 audio files at once, with one transcript each or all of them joined into one.
  • One project per couple. Keep the ceremony and the toasts in the same project. It is not a backup: with an active subscription, a file that goes 45 days without being opened is removed, with an email notice first.

Once the audio is processed, the ceremony becomes something you read, and the timestamps follow the player. An audio file has no Clips page: captioned vertical clips need the video, as covered in how to make a wedding highlight video.

If the project is already synced in your editor, export the timeline as .fcpxml or .xml and choose “My synced timeline” when you export (Studio and Agency). The timeline has to hold the audio you uploaded in full, with no cuts in it. The dialog asks, in seconds, where that file starts on the timeline: count from the timeline’s first frame and use the start of the file, even if you trimmed the upload down to the ceremony. The timecode calculator converts your editor’s timecode to seconds. The cut comes back on top of all your tracks.

Three limits: a Final Cut multicam clip comes in on its active angle only; a multicam in Premiere Pro or DaVinci Resolve XML isn’t read yet, so flatten the multicam on a copy of the timeline before exporting; and titles and adjustment layers are left out, while transitions become straight cuts. Without your timeline, an audio-only upload gives you an audio-only timeline.

What if the wedding audio came out bad?

ProblemCan it be saved?What to do
The lav’s wireless link droppedYes, with a backupUse the transmitter recording or the officiant’s lav
Clipped peak at 24-bitNot that passageSwitch to the safety track or the other source
”Clipped” peak in 32-bit floatYesLower the file’s gain in post
Wind or rubbing fabricBarelySwitch to the other source for that passage
Church reverbRarelyOnly a mic close to the mouth avoids it

Removing noise and isolating a voice is a job for your editor or dedicated audio software. We don’t do that and we don’t improve bad audio: we transcribe what was recorded. If you cleaned the audio up, upload the cleaned version.

Bad audio costs you in the transcript too. Proper names, words spoken through tears and passages under loud music are worth checking by ear, and a reception with many people talking at once loses accuracy in speaker separation. If the voice is simply quiet, the normalize audio tool makes reviewing easier, but it can’t bring back what the mic didn’t capture.

What do you get on each FilmScribe plan?

With the wedding audioProStudioAgency
Upload WAV, MP3 and M4A up to 10 GB and trim the rangeYesYesYes
Transcript with speakers and a timestamp on every wordYesYesYes
Chapters, emotions, favorites, MP3 passages, TXT, PDF and SRTYesYesYes
Speaker names, scored hooks and a paper edit from real linesNoYesYes
Cut timeline for Premiere Pro, DaVinci Resolve and Final Cut ProNoYesYes
Upload up to 20 audio files at onceNoNoYes

What no plan does:

  • No WAV out. Audio downloads as MP3, 128 kbps for passages and 192 kbps for the whole file. The WAV for your film is your original.
  • No emotion from tone of voice. Emotions come from the transcribed text. The processional, the first dance and the dance floor, with no speech, aren’t marked.
  • Nothing live. Everything starts from the finished recording.

During the trial, you get 1 upload at a time, with 3 passage downloads and 3 favorites per file. See what you get back for weddings and ceremonies, and the other guides for filmmakers on the weddings and events hub.

Other ways to handle wedding audio

  • Lav straight into the camera. No syncing needed, but the line now depends on the wireless link. Keep the transmitter recording too.
  • Timecode. Cameras and recorders that share timecode sync without relying on the waveform.
  • A dedicated sound person. At a large wedding, someone who only handles audio watches levels and batteries while you shoot.

Common wedding audio mistakes

  • Trusting a single source. A lav with no backup is a gamble.
  • Plugging the board into a mic input. The line signal arrives distorted and can’t be repaired.
  • Recording without headphones. You find the loose cable when you get home.
  • Leaving the camera’s auto gain on with an external mic. Shure recommends turning it off.
  • Formatting the card before the second copy. A card is not a backup.

The same plan works for a graduation, a milestone birthday or a corporate event: swap the vows for the main speech. What comes after the recording is in how to make an event recap video.

Frequently asked questions

How do I record wedding vows audio?

Put a lav on the groom, where it sits between both voices, and a second one on the officiant as the backup. Clip the mic outside the clothing, six to eight inches below the chin, with the cable taped down so nothing rubs. Turn on recording inside the transmitter and leave the camera mic running.

Where do you put a lav mic on the groom?

On the jacket lapel or the tie, outside the clothing, six to eight inches below the chin. To hide it, tuck it behind the boutonniere once the flowers are pinned and run the cable inside the jacket. The transmitter or recorder goes in the inside pocket. Skip the shirt collar: the sound gets muffled.

How do I record audio from the DJ's soundboard?

Ask the DJ for a free output on the board and plug in a recorder with its input set to line level. A mic-level input distorts. Set the level for the loudest moment, switch on the limiter and let it roll from dinner through the last toast, with a second recorder near a speaker.

What is a good wedding videography audio setup?

A setup that covers the day has a wireless lav that records inside the transmitter, for the groom and the officiant, a portable recorder with a line input, for the soundboard, and a shotgun mic on the camera for ambience and sync. Distance to the mouth decides the result, not the price tag.

Is a 32-bit float recorder worth it for weddings?

Yes, if you can get one. According to Zoom, with 32-bit float you don't set gain while recording and a peak that looks clipped can be recovered in post, at the cost of files about 33% larger than 24-bit. The format won't fix wind, fabric rubbing on the lav or a mic that sits far from the mouth.

How do I sync external audio with wedding video?

In your editor, by waveform. Keep the camera mic on for every take: it is the reference sound the editor matches against the recorder. In Final Cut Pro, the command is Clip > Synchronize Clips. A hand clap in front of the camera at the start gives you a manual sync point when the automatic one fails.

Does FilmScribe sync or clean up wedding audio?

No. Syncing cameras and external audio happens in your editor, and we don't remove noise or isolate voices. Our part comes after: we transcribe the lav or recorder audio with each speaker separated, plus chapters and emotions. The trial runs 3 days with 1 hour of material and needs a card on file.

Sources

The official documentation behind the numbers and rules in this guide.

  1. 01Audio Systems Guide for Video and Film Production(opens in a new tab) · Shure
  2. 02Wireless GO II User Guide(opens in a new tab) · RØDE
  3. 0332-Bit Float: Everything You Need to Know(opens in a new tab) · Zoom
  4. 04Sync audio and video in Final Cut Pro for Mac(opens in a new tab) · Apple
  5. 05DaVinci Resolve: Edit(opens in a new tab) · Blackmagic Design

Try it on your own recording. See the result before adding a card.

Upload a file or paste a YouTube link. Transcript, chapters, clips and captions are ready in minutes.